300-420 Questions Pass on Your First Attempt Dumps for CCNP Enterprise Certified [Q109-Q123]

Rate this post

300-420 Questions Pass on Your First Attempt Dumps for CCNP Enterprise Certified

300-420 Practice Test Pdf Exam Material

Cisco 300-420 exam covers a wide range of topics related to enterprise network design, including advanced routing and switching, network automation, security, and wireless networking. 300-420 exam is designed to test the candidate’s understanding of these topics and their ability to apply this knowledge to real-world scenarios. Candidates who pass the exam will be able to design and implement complex enterprise networks using Cisco technologies.

Q109. Refer to the exhibit. An architect must design a solution to connect bank site A with bank site B and support:
– network operation center monitoring end-to-end L3VPN and L2VPN
traffic
– company adding thousands of routes in the next two years
Which two BGP solutions must the design include? (Choose two.)

Establish full mesh IBGP peering with all routers in different IGP domains.

Redistribute different IGP domain routes in a BGP IPv4 routing instance.

Connect multiple IGP/LDP domains using a BGP IPv4 unicast family on the ABR.

Apply BGP policies on all routers to filter out ABR and PE loopback IP addresses.

Transport site routes using a BGP VPNv4 address family on the PE routers.

Q110. Refer to the exhibit. An architect must create a stable and scalable EIGRP solution for a customer. The design must:
– conserve bandwidth, memory, and CPU processing
– prevent suboptimal routing
– avoid any unnecessary queries
Which two solutions must the architect select? (Choose two.)

Prefix lists

Stub routing

Distribute lists

Route summarization

Static redistribution

Q111. Which design consideration must be made when using IPv6 overlay tunnels?

Overlay tunnels that connect isolated IPv6 networks can be considered a final IPv6 network architecture.

Overlay tunnels should only be considered as a transition technique toward a permanent solution.

Overlay tunnels can be configured only between border devices and require only the IPv6 protocol stack.

Overlay tunneling encapsulates IPv4 packets in IPv6 packets for delivery across an IPv6 infrastructure.

Q112. Drag and drop the steps WAN Edge performs when on-boarded into the Cisco SD-WAN overlay from the left into the order they are completed on the right.

Q113. Refer to the exhibit.

An engineer must optimize the traffic flow of the network. Which change provides a more efficient design between the access and the distribution layer?

Add a link between access switch A and access switch B

Reconfigure the distribution switch A to become the HSRP Active

Change the link between distribution switch A and distribution switch B to be a routed link

Create an EtherChannel link between distribution switch A and distribution switch B

Q114. Which two statements about VRRP object tracking are true? (Choose two)

The priority of a VRRP device can change in accordance with the up or down status of a VRRP object

The VRRP interface priority must be manually configured by the administrator

A VRRP group can track only one object at a time

VRRP can track the status of interfaces and routes

VRRP supports only interce tracking

Q115. Drag and drop the properties from the left onto the protocols they describe on the right.

Q116.

Refer to the exhibit. An engineer must design an address translation solution to provide Internet connectivity for the corporate network. The design Is restricted to the 172.16.168.0/22 subnet. Which solution must the engineer choose?

stateful NAT64

stateless NAT64

stateful NAT66

stateless NAT66

Q117. Which two Cisco ISE features provide benefits to our customers? (Choose two.)

enables them to set traffic encryption across the network

helps them accelerate application deployment and delivery

helps them stop and contain real-time threats

provides network access control

Q118. A network architect is enabling TV services in the LAN. The source will be streaming to the
239.1.1.1 group IP address. Dense mode is not allowed in the network. Multicast has already been enabled on all network devices in the LAN segment. Which action must the architect take to finalize the design?

Enable PIM SSM.

Enable PIM Auto-RP.

Enable PIM Anycast RP.

Enable PIM BSR.

Q119. An engineer must design an addressing plan for a small business using a single /24 network. Each department must have its own subnet. Drag and drop the subnets from the left onto the departments requirements that they fulfill on the right. Not all options are used.

Q120. A router running ISIS is showing high CPU and bandwidth utilization. An engineer discovers that the router is configured as L1/L2 and has L1 and L2 neighbors. Which step optimizes the design to address the issue?

Make this router a DIS for each of the interfaces

Disable the default behavior of advertising the default route on the L1/L2 router

Configure the router to be either L1 or L2

Configure each interface as either L1 or L2 circuit type

Q121. The customer solution requires QoS to support streaming multimedia over a WAN. An architect chooses to use Per-Hop Behavior.
Which solution should the engineer use to of mark traffic traveling between branch sites?

LLQ with DSCP EF

CBWFQ with DSCP AF3

CBWFQ with DSCP AF2

LLQ with DSCP AF4

Q122.

Refer to the exhibit. Which two solutions maximize the use of the links between the core and distribution layers? (Choose two.)

use multiple equal-cost links

use an IGP

use HSRP

use R-PVSTP+

use multiple unequal-cost links

Q123. Refer to the exhibit.

Refer to the exhibit. A customer experienced an unexpected network outage when the link between R1 and R2 went down. An architect must design a solution to ensure network continuity in the event the link fails again. Which solution should the design include?