Free NSE4_FGT_AD-7.6 Exam Study Guide for the NEW [Oct-2026] Dumps Test Engine [Q13-Q31]

Rate this post

Free NSE4_FGT_AD-7.6 Exam Study Guide for the NEW [Oct-2026] Dumps Test Engine

NSE4_FGT_AD-7.6 PDF Dumps Extremely Quick Way Of Preparation

Fortinet NSE4_FGT_AD-7.6 Exam Syllabus Topics:

Topic	Details
Topic 1	VPN: This domain focuses on implementing meshed or partially redundant IPsec VPN topologies for secure connections.
Topic 2	Deployment and System Configuration: This domain covers initial FortiGate setup, logging configuration and troubleshooting, FGCP HA cluster configuration, resource and connectivity diagnostics, FortiGate cloud deployments (CNF and VM), and FortiSASE administration with user onboarding.
Topic 3	Routing: This domain covers configuring static routes for packet forwarding and implementing SD-WAN to load balance traffic across multiple WAN links.
Topic 4	Content Inspection: This domain addresses inspecting encrypted traffic using certificates, understanding inspection modes and web filtering, configuring application control, deploying antivirus scanning modes, and implementing IPS for threat protection.
Topic 5	Firewall Policies and Authentication: This domain focuses on creating firewall policies, configuring SNAT and DNAT for address translation, implementing various authentication methods, and deploying FSSO for user identification.

NO.13 Refer to the exhibit.

What would be the impact of these settings on the Server certificate SNI check configuration on FortiGate?

FortiGate will accept and use the CN in the server certificate for URL filtering if the SNI does not match the CN or SAN fields.

FortiGate will accept the connection with a warning if the SNI does not match the CN or SAN fields.

FortiGate will close the connection if the SNI does not match the CN or SAN fields.

FortiGate will close the connection if the SNI does not match the CN and SAN fields

NO.14 Refer to the exhibits. The exhibits show a diagram of a FortiGate device connected to the network, and the firewall configuration.

An administrator created a Deny policy with default settings to deny Webserver access for Remote-User2.
The policy should work such that Remote-User1 must be able to access the Webserver while preventing Remote-User2 from accessing the Webserver.
Which additional configuration can the administrator add to a deny firewall policy, beyond the default behavior, to block Remote-User2 from accessing the Webserver?

Disable match-vip in the Allow_access policy

Configure a One-to-One IP Pool object in a new policy.

Set the Destination address as Webserver in the Deny policy.

Set the Destination address as Deny_IP in the Allow_access policy.

NO.15 Refer to the exhibits. An administrator configured the Web Filter Profile to block access to all social networking sites except Facebook. However, when users try to access Facebook.com, they are redirected to a FortiGuard web filtering block page.
Based on the exhibits, which configuration change must the administrator make to allow Facebook while blocking all other social networking sites?

Change the type as Simple in the Static URL Filter section.

Set the Social Networking action as warning in the FortiGuard Category Based Filter.

Change the Feature set of Web Filter Profile as Proxy-based.

Set the Action as Exempt for www.facebook.com in the Static URL Filter.

NO.16 Refer to the exhibits.

An administrator creates a new address object on the root FortiGate (Local-FortiGate) in the security fabric. After synchronization, this object is not available on the downstream FortiGate (ISFW).
What must the administrator do to synchronize the address object?

Change the csfsetting on both devices to set downstream-access enable.

Change the csfsetting on Local-FortiGate (root) to set fabric object-unification default.

Change the csfsetting on ISFW (downstream) to set authorization-request-type certificate.

Change the csfsetting on ISFW (downstream) to set configuration-sync local.

NO.17 Refer to the exhibit.
A RADIUS server configuration is shown.

An administrator added a configuration for a new RADIUS server While configuring, the administrator enabled Include in every user group What is the impact of enabling Include in every user group in a RADIUS configuration?

This option places the RADIUS server, and all users who can authenticate against that server, into every FortiGate user group.

This option places all FortiGate users and groups required to authenticate into the RADIUS server, which, in this case, is FortiAuthenticator.

This option places the RADIUS server, and all users who can authenticate against that server, into every RADIUS group.

This option places all users into every RADIUS user group, including groups that are used for the LDAP server on FortiGate.

NO.18 Refer to the exhibit. The administrator configured SD-WAN rules and set the FortiGate traffic log page to display SD-WAN-specific columns: SD-WAN Quality and SD- WAN Rule Name.
FortiGate allows the traffic according to policy ID 1 placed at the top. This is the policy that allows SD-WAN traffic. Despite these settings, the traffic logs do not show the name of the SD-WAN rule used to steer those traffic flows.
What could be the reason?

SD-WAN rule names do not appear immediately. The administrator must refresh the page.

There is no application control profile applied to the firewall policy.

FortiGate load balanced the traffic according to the implicit SD-WAN rule.

Destinations in the SD-WAN rules are configured for each application, but feature visibility is not enabled.

NO.19 Refer to the exhibits.

An administrator wants to add HQ-ISFW-2 in the Security Fabric. HQ-ISFW-2 is in the same subnet as HQ-ISFW. After configuring the Security Fabric settings on HQ-ISFW-2, the status stays Pending. What can be the two possible reasons? (Choose two answers)

Upstream FortiGate IP must be set to 10.0.11.254.

SAML Single Sign-On must be set to Manual.

HQ-ISFW-2 must be authorized on HQ-ISFW.

Management IP must be set to 10.0.13.254.

NO.20 Refer to the exhibit.

The NOC team connects to the FortiGate GUI with the NOC_Access admin profile. They request that their GUI sessions do not disconnect too early during inactivity. What must the administrator configure to answer this specific request from the NOC team?

Increase the admintimeout value under config system accprofile noc Access.

increase the of line value of the override idle Timeout parameter in the NOC_Access admin profile.

Move NOC_Access to the top of the list to ensure all profile settings take effect.

Ensure that all NOC_Access users are assigned the super_admin role to guarantee access.

NO.21 Refer to the exhibit. As an administrator you have created an IPS profile, but it is not performing as expected. While testing you got the output as shown in the exhibit.
What could be the possible reason of the diagnose output shown in the exhibit?

There is a no firewall policy configured with an IPS security profile.

FortiGate entered into IPS fail open state.

Administrator entered the command diagnose test application ipsmonitor 5.

Administrator entered the command diagnose test application ipsmonitor 99.

NO.22 You want to ensure that an SSL VPN user’s authenticated session does not remain active after they disconnect from the VPN.
Which configuration will ensure this?

Configure the firewall authentication session timeout to be lower than the SSL VPN session timeout.

Manually clear active firewall authentication sessions after a user disconnects.

Increase the SSL VPN idle timeout to reduce the chance of early disconnections.

Enable settings to force the firewall authentication session to end when the SSL VPN session ends

NO.23 Refer to the exhibits.

Based on the current HA status, an administrator updates the override and priority parameters on HQ-NGFW-
1 and HQ-NGFW-2 as shown in the exhibits.
What would be the expected outcome in the HA cluster?

HQ-NGFW-2 will take over as the primary because it has the override enable setting and higher priority than HQ-NGFW-1.

HQ-NGFW-1 will remain the primary because HQ-NGFW-2 has lower priority

The HA cluster will become out of sync because the override setting must match on all HA members.

HQ-NGFW-1 will synchronize the override disable setting with HQ-NGFW-2.

NO.24 Which two components are part of the secure internet access (SIA) agent-based mode on FortiSASE? (Choose two.)

VPN policies

The proxy auto-configuration (PAC) file

FortiExtender

FortiSASE Firewall-as-a-Service (FWaaS)

NO.25 Refer to the exhibits, which show the system performance output and the default configuration of high memory usage thresholds in a FortiGate.

Based on the system performance output, what can be the two possible outcomes? (Choose two.)

FortiGate will start sending all files to FortiSandbox for inspection.

Administrators can access FortiGate only through the console port.

FortiGate has entered conserve mode.

Administrators cannot change the configuration.

NO.26 Refer to the exhibits.

You have implemented the application sensor and the corresponding firewall policy as shown in the exhibits.
You cannot access any of the Google applications, but you are able to access www.fortinet.com.
Which two actions would you take to resolve the issue? (Choose two.)

Set SSL inspection to deep-content inspection.

Move up Google in the Application and Filter Overrides section to set its priority lot

Add “Google”.com to the URL category in the security profile.

Change the Inspection mode to Flow-based

Set the action for Google in the Application and Filter Overrides section to Allow

NO.27 When FortiGate performs SSL/SSH full inspection, you can decide how it should react when it detects an invalid certificate.
Which three actions are valid actions that FortiGate can perform when it detects an invalid certificate? (Choose three.)

Allow

Trust & Allow

Allow & Warning

Block

Block & Warning

NO.28 Refer to the exhibits.

The system performance output and default configuration of high memory usage thresholds on a FortiGate device are shown.
Based on the system performance output, what are the two possible outcomes? (Choose two.)

Administrators can access FortiGate only through the console port.

FortiGate has entered conserve mode.

FortiGate drops new sessions.

Administrators can change the configuration.

NO.29 Refer to the exhibit. Which two statements are true about the routing entries in this database table? (Choose two.)

All of the entries in the routing database table are installed in the FortiGate routing table.

The port2 interface is marked as inactive.

Both default routes have different administrative distances.

The default route on port2 is marked as the standby route.

NO.30 A network administrator wants to set up redundant IPsec VPN tunnels on FortiGate by using two IPsec VPN tunnels and static routes.
All traffic must be routed through the primary tunnel when both tunnels are up. The secondary tunnel must be used only if the primary tunnel goes down. In addition, FortiGate should be able to detect a dead tunnel to speed up tunnel failover.
Which two key configuration changes must the administrator make on FortiGate to meet the requirements? (Choose two.)

In the phase1-interface, enable npu-offload to detect a dead tunnel.

Configure a lower distance on the static route for the primary tunnel, and a higher distance on the static route for the secondary tunnel.

Enable Dead Peer Detection.

Use the VPN wizard to create an IPsec template for a redundant IPsec VPN tunnel.

NO.31 When configuring firewall policies which of the following is true regarding the policy ID? (Choose two.)

A firewall policy ID identifies the order of policy execution in firewall policies.

A policy ID cannot be modified once a policy is created.

You can create a policy in CLI with policy ID 0

It is mandatory to provide a policy ID while creating a firewall policy regardless of GUI or CLI.

Enhance your career with NSE4_FGT_AD-7.6 PDF Dumps – True Fortinet Exam Questions: https://www.examstorrent.com/NSE4_FGT_AD-7.6-exam-dumps-torrent.html

Fortinet NSE4_FGT_AD-7.6 Exam Syllabus Topics:

admin

You May Also Like

Leave a Reply Cancel reply